ADICON Support Forum Applied Digital, Inc.
You are not logged in. [Log In] Home » Forums » ADI Products » Ocelot HA Controller » ocelot Polling speed
Register User       Forum List       Calendar       FAQ
Page 2 of 2 <12
Topic Options
#22416 - 03/15/11 07:36 AM Re: ocelot Polling speed [Re: jasemilly]
Guy Lavoie Administrator Offline
Beyond All Hope
*****

Registered: 12/21/02
Posts: 6421
Loc: Montreal, QC, Canada
Hmm, hard to say what might be the problem. You should try it with just the first module connected and see if that works. If so then add a couple more, etc. Looks like something went wrong along the way.
_________________________
"If you don't know what you're doing, do it neatly..."

Top
#22417 - 03/15/11 07:44 AM Re: ocelot Polling speed [Re: jasemilly]
jasemilly Offline
junior


Registered: 10/07/10
Posts: 41
just redone some of the connections and i have everything back. But it's slow. I have a contact closure and it takes about 2 seconds before the x10 signal is fired.
Top
#22418 - 03/15/11 08:58 AM Re: ocelot Polling speed [Re: jasemilly]
Guy Lavoie Administrator Offline
Beyond All Hope
*****

Registered: 12/21/02
Posts: 6421
Loc: Montreal, QC, Canada
That kind of delay is pretty well normal, especially if you have several expansion modules like that. The bus latency and the time required to send X10 commands will make the delay an average of 1.5 to 2 seconds.
_________________________
"If you don't know what you're doing, do it neatly..."

Top
#22419 - 03/15/11 11:24 AM Re: ocelot Polling speed [Re: Guy Lavoie]
jasemilly Offline
junior


Registered: 10/07/10
Posts: 41
ok will think of some way around.

not sure whats happened I downloaded a little test program was having an issue with an x10 module.

I then loaded my normal project back into the Ocelot and now my ocelot isn't transmitting x10 codes.
apart from the x100 log displays e3 continuly.

I have tried to load the program again but has made no difference. I have powered down the unit for now.

What else can I do ???

thanks
Top
#22420 - 03/15/11 11:29 AM Re: ocelot Polling speed [Re: jasemilly]
Guy Lavoie Administrator Offline
Beyond All Hope
*****

Registered: 12/21/02
Posts: 6421
Loc: Montreal, QC, Canada
one word of (sanity) warning: if you leave the X10 monitoring window open in C-Max, the Ocelot will not transmit any X10 commands that you try to send from C-MAx. Close the monitoring window first.

The E3 thing is odd. Is that code anywhere in your program?
_________________________
"If you don't know what you're doing, do it neatly..."

Top
#22421 - 03/15/11 11:36 AM Re: ocelot Polling speed [Re: Guy Lavoie]
jasemilly Offline
junior


Registered: 10/07/10
Posts: 41
Ok thanks for that, I not sending commands while monitoring.

I have left the ocelot powered off for 5 minutes turned it back on and am having this problem.

the module e3 is making a very quiet clciking noise as if it is recieving a command. The modules make this noise when they are addressed before a louder click when a on or off command is actually sent.

thanks
Top
#22422 - 03/15/11 11:37 AM Re: ocelot Polling speed [Re: jasemilly]
Guy Lavoie Administrator Offline
Beyond All Hope
*****

Registered: 12/21/02
Posts: 6421
Loc: Montreal, QC, Canada
try reloading the executive and then your program.
_________________________
"If you don't know what you're doing, do it neatly..."

Top
#22424 - 03/16/11 06:48 AM Re: ocelot Polling speed [Re: Guy Lavoie]
jasemilly Offline
junior


Registered: 10/07/10
Posts: 41
sorted it left it off for a good 10 minutes and then reloaded the executive and the program and it sorted itself out.

thanks
Top
Page 2 of 2 <12


Moderator:  Dan Smith, Monte G, ADI Tech Support, Guy Lavoie 
Hop to:
Who's Online
1 registered (dasdasd) and 17 anonymous users online.
details
Recent Posts
baby carriers
by apsun
05/19/12 06:53 PM
The Foremost Selected Infant Carriers
by dasdasd
05/19/12 06:33 PM
Whole house music.
by Guy Lavoie
05/19/12 04:13 PM
cmax 2.0
by Presidio Dog
05/12/12 10:42 PM
Dead SpeakEasy
by ADI Tech Support
05/04/12 09:50 AM
Shout Box

Newest Members
dasdasd, apsun, modularko, Presidio Dog, appoa
2765 Registered Users
Forum Stats
2765 Members
19 Forums
3856 Topics
22808 Posts

Max Online: 67 @ 08/16/11 03:08 PM
May
Su M Tu W Th F Sa
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31
My Cookies · Mark all read Powered by UBB.threads™ Contact Us · Home · Top