|
I cannot figure this out
I have rather simple setup at this time
Leopard II, 1 X Bobcat L, 3 X Bobcat T, 3 X Bobcat H and 3 X SECU16
This is some of my code so far:
0075 - IF Module #1 -BOBCAT-L is < 999 //
0076 - THEN Load Data to: Variable #3 //
0077 - THEN Variable #3 - 100 //
0078 - THEN Variable #3 * 100 //
0079 - THEN Variable #3 / 256 //
0080 - THEN Variable #4 = Variable #3 //
0081 - //
0082 - IF Module #2 -BOBCAT-T is > -21 //
0083 - THEN Load Data to: Variable #0 //
0084 - THEN Variable #0 + 80 //
0085 - THEN Variable #0 - 32 //
0086 - THEN Variable #0 * 5 //
0087 - THEN Variable #0 / 9 //
0088 - THEN Variable #0 - 100 //
0089 - THEN Variable #17 = Variable #0 //
0090 - THEN Variable #0 = 0 //
0091 - //
0092 - IF Module #3 -BOBCAT-T is > -21 //
0093 - THEN Load Data to: Variable #0 //
0094 - THEN Variable #0 + 80 //
0095 - THEN Variable #0 - 32 //
0096 - THEN Variable #0 * 5 //
0097 - THEN Variable #0 / 9 //
0098 - THEN Variable #0 - 100 //
0099 - THEN Variable #18 = Variable #0 //
0100 - THEN Variable #0 = 0 //
0101 - //
0102 - IF Module #4 -BOBCAT-T is > -21 //
0103 - THEN Load Data to: Variable #0 //
0104 - THEN Variable #0 + 80 //
0105 - THEN Variable #0 - 32 //
0106 - THEN Variable #0 * 5 //
0107 - THEN Variable #0 / 9 //
0108 - THEN Variable #0 - 100 //
0109 - THEN Variable #19 = Variable #0 //
0110 - THEN Variable #0 = 0 //
0111 - //
0112 - IF Module #5 -BOBCAT-H is < 256 //
0113 - THEN Load Data to: Variable #0 //
0114 - THEN Variable #0 - 100 //
0115 - THEN Variable #20 = Variable #0 //
0116 - //
0117 - IF Module #6 -BOBCAT-H is < 256 //
0118 - THEN Load Data to: Variable #0 //
0119 - THEN Variable #0 - 100 //
0120 - THEN Variable #21 = Variable #0 //
0121 - //
0122 - IF Module #7 -BOBCAT-H is < 256 //
0123 - THEN Load Data to: Variable #0 //
0124 - THEN Variable #0 - 100 //
0125 - THEN Variable #22 = Variable #0 //
PROBLEMs are my temperature and humidity display readings
All the time my temp and humidity sensors works fine according to debug window and behave
according to the environmental conditions, (at this point all sensors are in the same room)
but my Leopard display is “acting up”
for example the temp condition inside the room is 22C all 3 sensors displaying data and showing most of the time 22C
but occasionally one of them will show 72C than all back to normal than another display will go back to 68C, etc
It’s all happening quickly for about a second ,they just erratically changing and than back to normal
This all refers I think to all of my temperature as well as humidity displays they all behave that way
I hope this all make sense
Please help!!!
1021
| 
